Design Freestanding Slipper Bath - L1680 x W720mm BeBa_12161

Question from Rebecca: Asked on 10/06/2017 Does this bath come assembled, or is it in several pieces? Does it need to be attached to the floor, or is it sturdy enough to be freestanding, with no additional support?

Question from Lisa Nicholls: Asked on 13/05/2017 Im not sure what is the best waste for this bath?

Answer from Ryan Moore Hi there

Thank you for your question.

Please make a note of this item. This would be the most suitable.

Extended Bath Pop Up Waste

Product Code: 6296

If you would like any further information, or if you would like to place an order, please do not hesitate to contact me

Thank you again

Ryan Moore
Manchester Showroom Sales Assistant
Better Bathrooms Manchester

Telephone: 0161 667 6560
Email: ryan.moore@betterbathrooms.com
Website: www.betterbathrooms.com

Question from Victoria: Asked on 13/01/2017 Is the overflow round or a slit as per the smaller model?

Answer from Colin Frain Hi,

Thank you for your question.

The bigger one is a round design waste.

If you need any more info or would like to place an order send the items you are wishing to buy to my email address along with your telephone number and i can check the items are compatible and that you are not missing any vital items.


Kind Regards,

Colin Frain
Sales Advisor
Manchester Showroom
Telephone: 0161 667 6560
colin.frain@betterbathrooms.com

Question from corinne peters: Asked on 04/06/2016 What is the width of the slipper bath?

That does not appear to be on the info

A reply asap please

Answer from Nathan McGregor Hello.

Thank you for your question.

This bath is approximately 720mm at it's widest point.

Regards.

Question from Mark: Asked on 09/07/2015 Would I have to lower my waste pipe so it sits flush with floor to accommodate this

Answer from Nathan McGregor Hello.

Thank you for your question.

Yes you would have to sink the waste into the floor to get the correct fall for the water supply.

Regards.

Question from Charley : Asked on 22/02/2015 Do I need to buy a waste and overflow for this bath? If so which ones?

Answer from Matt Clarke Hi,

The correct waste is 6296. If you would like to order this please call me on 0161 6676560 my name is Matt.

Regards

Question from Mike C: Asked on 04/11/2014 What's the position of the waste drain in relation to the sides?

Answer from Jamie H Hi,

Thank you for your question the waste is approximately located 100mm from the end of the bath. If you have any further questions please free to give us a call on 0161 667 65 60

Question from Alan Watson: Asked on 27/08/2014 Can I use a combined overflow filler on this bath with remote taps.

Answer from Nathan McGregor Hello.

This would not be possible with this freestanding bath.

Regards.

Question from Chris Perry: Asked on 14/06/2014 can you advise if this is double skinned acrylic, the internal dimensions, and thickness of acrylic please?
Thanks

Answer from Matt Clarke Hi and thank you for your question,

Yes this is a twin skinned bath. The thickness of the acrylic is 5mm approx. The internal dimension vary due to the curvature of the bath please be more specific as to which exact measurements you need.

Regards

Question from Graham: Asked on 12/03/2014 With the "to the floor" design and no joins at the rim - how do you go about connecting the waste and taps if you go for the drilling and mounted taps option?
Thanks
Graham

Answer from Peter Hi,

Thank you for your question.

There is a service void between the 2 sheets of acrylic for you to be able to install the taps.

Question from kevin grint: Asked on 12/02/2013

Design Slipper Bath - Product Details Product Code: 6940 I was looking at your web site regarding above product and watch the video and when it shows the mesurement i think you have got it wrong way round as height is lenght and the other way around.

Answer from Anthony

Hi there

The dimensions for the bath are: Length 1680mm, Width 720mm, Height at Tallest Point 740mm, Height at Lowest Point 590mm. 

Question from Mimi Opra: Asked on 03/11/2012

What will be the total boxed weight of this bath?

Answer from Mike B

Hi there,

The total boxed weight of this item is 39kg - but please do consider a tolerance of approximately 2kg. 

Question from Cora McDonald: Asked on 14/10/2012

Hello

Does this bath have an overflow?

Answer from Lee

Hello

Yes the design slipper bath comes with a overflow that is pre drilled into the bath during the manufacturing process. If you are looking at any of the other bathrooms on our website they all come with an overflow. 

Question from ANGELA LONG: Asked on 09/06/2012 Which bath wastes are suitable for this bath? How thick is the bath?

Answer from Anthony Hi there,

The bath is 5mm thick. Product code 1662 is the correct waste.

Question from Dianne: Asked on 26/02/2012 What is the width of the narrow end of the bath. Is it possible to mount taps on the bath itself or do they need to be wall/floor mounted?

Answer from Anthony Hi there,

The width at the narrow end is approximately 640mm. Taps can be mounted on the bath at the narrow end, the holes are not pre-drilled for the taps.

Question from borbala: Asked on 18/02/2012 Can you please confirm what is the internal (straight) length of the tub?

Also can you please confirm that the joins are not visible at the bath edge?

Answer from Anthony Hi there,

The internal (straight) length of the Design Slipper Bath is approximately 1100mm.

The joins are not visable on the bath.

Question from Nicky Margrave-Jones: Asked on 08/01/2012 If I were to buy this bath now, please could I have a delivery date in February?

Answer from probertshaw HI, I'm afraid not, we cannot delay the despatch of any orders. We are fully stocked for the sale and have no space available for storage. Any goods ordered in Jan must be delivered within 3 - 5 days.